Ordered a bolt-on. Well, I guess two(?) bolt-ons
Nice!
06-02-2011, 03:38 PM
#32
Senior Members
Join Date: Jun 2008
Location: Chino Hills
Posts: 1,017
Likes: 0
Received 2 Likes
on
2 Posts
My Ride: 545I SMG
Guess what arrived..finally, after 6 months... 
Attachment 121708
The quality of the headers is good. I might get in there with a grinder and smooth out a couple welds, but aside from that I think they will be an improvement over the OEM exhaust manifolds. Can't wait to get these installed. I'm may install them myself.
In the process of setting up an appointment to get my car baselined again before the installation since I've made some changes since my last dyno run.
Anybody opposed to using header wrap other than the fact that it's ugly?
Attachment 121708
The quality of the headers is good. I might get in there with a grinder and smooth out a couple welds, but aside from that I think they will be an improvement over the OEM exhaust manifolds. Can't wait to get these installed. I'm may install them myself.
In the process of setting up an appointment to get my car baselined again before the installation since I've made some changes since my last dyno run.
Anybody opposed to using header wrap other than the fact that it's ugly?
Can't wait to see the hp improvement.
06-23-2011, 10:28 AM
#34
Senior Members
Thread Starter
Just got back from dropping the car off at the shop to get the headers installed! The following will be performed on the car over the next day:
After the headers are installed, I'll drive the car a mile or so to the exhaust shop. When the car is there, they will:
- Fabricate sleeve-type collector reducers to butt up to my existing magnaflow setup.
- Weld bungs on both header collectors so the pre-cat sensors can be fixed to the new system
- Extend the pre-cat sensor wires so they reach the new bungs
- Tie the post-cat sensors off to the side somewhere (maybe find simulators?..dunno yet)
Once that is done, I'll drive the car back to the shop that installed my headers and we'll do the following:
- Dyno the car with the headers (DynoJet)
- Dyno the car with the OEM exhaust manifolds (DynoJet)
- Install the headers (in-turn removing the cats)
- Install the headers (in-turn removing the cats)
After the headers are installed, I'll drive the car a mile or so to the exhaust shop. When the car is there, they will:
- Fabricate sleeve-type collector reducers to butt up to my existing magnaflow setup.
- Weld bungs on both header collectors so the pre-cat sensors can be fixed to the new system
- Extend the pre-cat sensor wires so they reach the new bungs
- Tie the post-cat sensors off to the side somewhere (maybe find simulators?..dunno yet)
Once that is done, I'll drive the car back to the shop that installed my headers and we'll do the following:
- Dyno the car with the headers (DynoJet)
06-23-2011, 11:46 AM
#35
Senior Members
Join Date: May 2010
Location: Portland, OR
Posts: 838
Likes: 0
Received 0 Likes
on
0 Posts
My Ride: 2005 545i Alpine White Premium package, Sport package, Nav, HUD, PDC
WOW!! You must be so excited, especially after waiting half a year!! Please do post the dyno when you get a chance, thanks!
06-23-2011, 12:02 PM
#36
Senior Members
Thread Starter
I'll definately post the dyno results. Hopefully this shop will give me the overlayed (before/after) results in a .JPG format like the last shop did. That would be cool.
06-23-2011, 09:26 PM
#38
Senior Members
Thread Starter
06-24-2011, 09:15 AM
#39
Senior Members
Thread Starter
...here are a couple "before" photos. The technician was removing the motor mounts when I dropped by so the original exhaust parts were still in tact:
Engine support for holding the engine in place while the subframe is lowered:
The subframe:
Exhaust manifolds:
Engine support for holding the engine in place while the subframe is lowered:
The subframe:
Exhaust manifolds:
06-24-2011, 09:15 PM
#40
Senior Members
Thread Starter
You guys can thank John at Carb Connection for the following photos. Every now and then you encounter that individual who gets it. John gets it. Not only that but he has a great deal of knowledge working with BMW's and also understands that some of his customers want to learn and witness their car being transformed. John was kind enough to invite me to the shop to let me hang out, take photos, watch, and learn. These iPhone photos are a testament to the quality of his work and his willingness to share the specifics of installing headers on the v8 e60. Thank you John.
Lowering the tranny a couple inches along with the sub-frame gave John enough space to get at the exhaust manifolds from below:
Not long after, he removed the passenger and drivers side exhaust manifolds:
Here is a comparison between the OEM manifolds and the Supersprint headers:
Just for fun I slid the OEM manifolds on to the cat-back system:
Lowering the tranny a couple inches along with the sub-frame gave John enough space to get at the exhaust manifolds from below:
Not long after, he removed the passenger and drivers side exhaust manifolds:
Here is a comparison between the OEM manifolds and the Supersprint headers:
Just for fun I slid the OEM manifolds on to the cat-back system
:
