Squealing Brake - Right side only
#1
New Members
Thread Starter
![Default](https://5series.net/forums/images/icons/icon1.gif)
Hey everyone,
So I posted a thread a bit ago about my steering wheel shaking when braking and I have since changed my front discs and pads. That problem has been fixed!
But now...My right brake squeaks/squeals when I brake. I have broken in the brakes and specifically stopped from 100km an hour to about 20 and then 60km an hour to 20 about 5 or 6 times each.
At first it was more prevalent when I would brake from higher speeds, but since braking them in, I've noticed it's a lower speeds.
Everything during the change was done the same but I'll be honest, I didn't toqrue the slide pins in at 22ft lb...I just made sure they were snug. I made sure to grease the metal on metal points between the caliper bracket and pads, made sure to lube the pins with Silicone lube. Now I didn't grease the back of the pads because I noticed they came with shims.
Any suggestions on hat's wrong?
Thanks,
V.
So I posted a thread a bit ago about my steering wheel shaking when braking and I have since changed my front discs and pads. That problem has been fixed!
But now...My right brake squeaks/squeals when I brake. I have broken in the brakes and specifically stopped from 100km an hour to about 20 and then 60km an hour to 20 about 5 or 6 times each.
At first it was more prevalent when I would brake from higher speeds, but since braking them in, I've noticed it's a lower speeds.
Everything during the change was done the same but I'll be honest, I didn't toqrue the slide pins in at 22ft lb...I just made sure they were snug. I made sure to grease the metal on metal points between the caliper bracket and pads, made sure to lube the pins with Silicone lube. Now I didn't grease the back of the pads because I noticed they came with shims.
Any suggestions on hat's wrong?
Thanks,
V.
#3
New Members
Thread Starter
![Default](https://5series.net/forums/images/icons/icon1.gif)
Yea eh? I've been doing more research and I think I'm gonna get some brake quiet stuff and put it on the back of the pads. I noticed there was red rubbery stuff on the old pads and found out that was the CRC brake quiet. Fingers crossed!
#4
Super Moderator
![](https://5series.net/forums/images/ranks/veteran_army.png)
Join Date: Jul 2011
Location: Augusta, GA
Posts: 3,594
Likes: 0
Received 311 Likes
on
298 Posts
My Ride: 05 530i M54
Model Year: 05 530i
Engine: 3.0 M54
![Default](https://5series.net/forums/images/icons/icon1.gif)
Originally Posted by Valhalla519
Yea eh? I've been doing more research and I think I'm gonna get some brake quiet stuff and put it on the back of the pads. I noticed there was red rubbery stuff on the old pads and found out that was the CRC brake quiet. Fingers crossed!
The following users liked this post:
Valhalla519 (06-02-2020)
#5
New Members
Thread Starter
![Default](https://5series.net/forums/images/icons/icon1.gif)
I'm gonna get the brake quiet stuff just to have more piece of mind. I don't wanna have to take the wheel and caliper off again haha.
#6
Super Moderator
![Default](https://5series.net/forums/images/icons/icon1.gif)
I never lube my brakes and have never had any problems with noise.
One time I had an annoying squeak at low speeds and it turned out to be my brake wear indicator.
One time I had an annoying squeak at low speeds and it turned out to be my brake wear indicator.
#7
New Members
Thread Starter
#10
New Members
Thread Starter
![Default](https://5series.net/forums/images/icons/icon1.gif)
So I applied the brake quiet solution but they still squeal. I've noticed now that I hear a squeak even when I'm not breaking!
I've ordered higher quality and move expensive brake pads off rock auto.
The new thing I noticed is that the outer brake pad was loose when put into the caliper, like the retention clip wasn't doing it's job...could that be the issue?
Thanks.
I've ordered higher quality and move expensive brake pads off rock auto.
The new thing I noticed is that the outer brake pad was loose when put into the caliper, like the retention clip wasn't doing it's job...could that be the issue?
Thanks.