Oil Leak at oil filter area
#1
Senior Members
Thread Starter
Join Date: Jan 2011
Location: UpState SC
Posts: 2,348
Likes: 0
Received 3 Likes
on
3 Posts
My Ride: 2008 535i LCI with sports/premium package, Sports trans with paddle shifters, CF emblems, JB4 Software, Dinan Exhaust, Navigation, M5Tech body kit, Carbon wrap interrior trim and CIC Controller.
Oil Leak at oil filter area
I've noticed an oil that has popped up and jsut the other day I cleaned it well and then two days later it's back to this again. I have found a few threads that show the seal repalcement for the oil filter housing but I am not sure if this is the same thing or not, it looks like it is though.
Last edited by tonyb635; 02-13-2013 at 08:05 AM.
#2
Senior Members
Thread Starter
Join Date: Jan 2011
Location: UpState SC
Posts: 2,348
Likes: 0
Received 3 Likes
on
3 Posts
My Ride: 2008 535i LCI with sports/premium package, Sports trans with paddle shifters, CF emblems, JB4 Software, Dinan Exhaust, Navigation, M5Tech body kit, Carbon wrap interrior trim and CIC Controller.
More Pics
Additional Pics
#4
Senior Members
Thread Starter
Join Date: Jan 2011
Location: UpState SC
Posts: 2,348
Likes: 0
Received 3 Likes
on
3 Posts
My Ride: 2008 535i LCI with sports/premium package, Sports trans with paddle shifters, CF emblems, JB4 Software, Dinan Exhaust, Navigation, M5Tech body kit, Carbon wrap interrior trim and CIC Controller.
Yesterday I checked the cap and it did turn just a very small amount. I don't think it was enough to say this is the problem though.
#5
New Members
Join Date: Jan 2013
Location: atlanta
Posts: 228
Likes: 0
Received 0 Likes
on
0 Posts
My Ride: 2005 545i Sport
Who did the last oil change?
You mentioned that the filter was further tightened which could indicate that it wasn't tightened enough to start. If it continues to leak, apply more torque but it doesn't take a lot of strength to properly tighten.
Do you own a torque wrench? Check the correct torque and see where your install matches. If the torque wrench "clicks" immediately after you try to tighten (provided you set it correctly) then its not a torque issue, but probably an o-ring problem.
The new oil filter "O" ring should be pre-oiled before installing so that it glides into position.
The "O" ring needs to be properly positioned on the oil filter housing, there is a ringed notch for its placement. This notch should be free of debris across its entire circumference. Clean it out with an old toothbrush if necessary, then wipe clean using a clean rag, or even a paper towel formed to fit into the o-ring notch.
Who made the oil filter that was installed? I recommend only Mahle, Hengst, Mann or Bosch. Stay away from the SLIGHTLY cheaper Korean and other Asian stuff.
You mentioned that the filter was further tightened which could indicate that it wasn't tightened enough to start. If it continues to leak, apply more torque but it doesn't take a lot of strength to properly tighten.
Do you own a torque wrench? Check the correct torque and see where your install matches. If the torque wrench "clicks" immediately after you try to tighten (provided you set it correctly) then its not a torque issue, but probably an o-ring problem.
The new oil filter "O" ring should be pre-oiled before installing so that it glides into position.
The "O" ring needs to be properly positioned on the oil filter housing, there is a ringed notch for its placement. This notch should be free of debris across its entire circumference. Clean it out with an old toothbrush if necessary, then wipe clean using a clean rag, or even a paper towel formed to fit into the o-ring notch.
Who made the oil filter that was installed? I recommend only Mahle, Hengst, Mann or Bosch. Stay away from the SLIGHTLY cheaper Korean and other Asian stuff.
#6
Members
Senior Members
Join Date: Apr 2012
Location: Concord, CA
Posts: 953
Likes: 0
Received 0 Likes
on
0 Posts
My Ride: Alpine E60, '09 535i-Premium, Sport and Comfort Access PackageMods: Lux H8 V3 Angel Eyes, Weisslicht LED license plate lights, Interior LED lights, RPI Scoop, Matte Black Grills, Smoked LED side markers & side reflectors, 35% tint all around, and a 3
That's a common issue with the oil filter housing. Mine had started leaking and had the housing gasket, cooler gasket, and oil line o rings. Haven't had a problem since.
#7
Senior Members
Thread Starter
Join Date: Jan 2011
Location: UpState SC
Posts: 2,348
Likes: 0
Received 3 Likes
on
3 Posts
My Ride: 2008 535i LCI with sports/premium package, Sports trans with paddle shifters, CF emblems, JB4 Software, Dinan Exhaust, Navigation, M5Tech body kit, Carbon wrap interrior trim and CIC Controller.
I plan to clean it up today a see if that small turn help any. Otherwise I guess I'll be looking into getting these gaskets replaced. It seems to be getting worse...
#9
Contributors
Join Date: May 2009
Location: SoCal
Posts: 10,496
Likes: 0
Received 2 Likes
on
2 Posts
My Ride: 2008 550I LOADED, all options except HUD and NV
I know it is common on the M54 motor to have the oil filter housing gasket leak over time, I have never heard of it in the N55 motors though. Interesting, you would think BMW had revised the design for better longevity.
#10
Members
Senior Members
Have had this same problem. Slow pooling of oil in the same place. The problem was a messed up (crimped) o-ring gasket that goes on the oil filter cap. As someone else recommends, get a new filter from BMW and take the cap off and replace the o-ring.